find remote control like "Air Remote Mouse MX3" which perhaps costs even a little more but which has a front side with different programmable "IR" commands to control the TV, a decent wi.fi keyboard on the back and a comfortable enough air mouse functionality. I will now look for the other way indicated by some of you: i.e. From what I've seen so far on the net, this is a limitation of this object and there is not simply solution. Instead this was not the caseįlirc translates "everything" but has no outgoing commands between its "controllers" that allow you to move the mouse. Unfortunately I assumed that I could do this again with Flirc USB. So I controlled both the PC part and Kodi once started. I must say that it is a beautiful object but it has a limit, at least that's how I understood until now, which does not allow it to do what I used to do with my old nuc7i3bnh and my Logitech Harmony 300 universal remote controlĪs you recall the nuc7i3bnh had a built in infrared receiver and I had programmed "Microsoft MCE Keyboard" where I was able to use numbers from the Harmony remote to move the mouse. Yesterday I received the Flirc stick I ordered on Ebay for €25. Please continue reading on the Flirc Website or browse the web for further information. Using the Flirc software (screenshot below) you can record any additional Infrared command you need and assign it to a particular button on the remote. This cheap Infrared Receiver can be easily plugged into the front USB port and supports Kodi very well. But if you already own a Logitech Harmony, then add the Flirc USB to your NUC.Unfortunately, this product has been discontinued. From my point of view, the Logitech Harmony Elite Remote Control (Infrared) is still the ne plus ultra to control an entire home cinema. CEC can be very balky, since unfortunately there is also a certain rank growth in the different device implementations and compatibility issues can therefore arise. The advantage is that you should be able to operate up to 15 devices solely with the TV remote control. It's been part of the HDMI spec for 20 years now. However, this solution does not support the HDMI feature Consumer Electronics Control (CEC). This is the best that modern HDMI 2.1 TVs support. In addition to 8K, you can also use 4K 120 Hz 10-bit HDR RGB 4:4:4 with a bandwidth of 40 Gbps. Use an USB-C/Thunderbolt > HDMI FRL cable to unleash the full power of the Intel Iris Xe Graphics.The WAKE key feature is going to be implemented but I can't tell you any time frame when will that happen.I'd recommend the following to use a NUC as HTPC as I do with Kodi: When the WAKE key is recorded, only that key will wake the PC.Īt this moment, the new Flirc (the metal one) has wake function enabled by default and supports only waking up by any known key. You can change that by going to Full Keyboard controller in Flirc GUI and recording the WAKE key. By default Flirc will wake the PC upon pressing any remote key known to it (like I've mentioned in my previous post - this means any key that is recorded and recognised by Flirc). When it's checked then there are two modes of operation. Make sure that the Sleep Detection is checked. The Harmony software will guide you through entering the manufacturer and model. Open Flirc GUI and go to File menu and Advanced. The old Flirc (the clear plastic one) may need some configuration. I am trying to be able to use one profile when PowerDVD is launched and the another profile for the Kodi box when I close PDVD. However, with the way FLIRC works, theres only one profile. If you are able to wake your PC using USB keyboard then it also should work with Flirc. My Kodi box launches PowerDVD when it recognizes a blu-ray in the drive. There may be an option in the BIOS/UEFI you need to enable. If this doesn't work for you then Flirc also won't be able to do that. You should be able to wake your PC by pressing a key on the keyboard. You can test if the wake up function does work at all by connecting an USB keyboard and going to suspend mode. The feature is also software controlled so OS also needs to properly configure the motherboard when going into suspend to allow waking from USB (this usually happens by default unless there's some incompatibility between operating system and the motherboard hardware). If the hardware itself supports waking by USB devices then it should work out of the box.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |